| Customization: | Available |
|---|---|
| Application: | Industry |
| Hardness: | Hardened |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Tie Rod Ta Series Shaft Mounted Gearbox
Mounting type: Tie rod Hanging shaft mounted
Out-put shaft: Single key hollow shaft, each model can select three hollow diameter at most.
Gearbox Housing: Hard Iron Steel, can be used outside.
Anti run back device: Can meet any model, It's very convenient to be mounted.
ATA series shaft mounted gear reducer is with hardened gears have high carrying capacity, smooth transmission, light weight, low energy consumption and so on characteristics. Input shaft of reducer is connected with motor by belt pulley, output hollow shaft linked with a key. It could be instead of electric drum to be power source for a belt conveyors and lifting equipments. ATA series could be with back-stop to avoid the working machine back skating, and mounted by tie rod! Mounted conveniently! It is widely applied in the mining equipments, Concrete mixing batching plant, Stone Crushers, Sand making production line and other belt conveyor mechanical transmission areas.
Mechanical belt conveyor drive system is composed by ATA shaft-mounted gearbox, torque arm, pulleys and motors. whose power transmission from the motor to the gearbox through the pulley, and then gearbox passed to the drive pulley through the hollow shaft and the gearbox is fixed by torque arm, anti-down device can be configured. The system is convenient to install use and maintain.
The scope of ATA shaft mounted gearbox:
Agriculture, commerce, telecommunications industry, the food industry, tobacco industry, automobile industry, cement industry, mining industry, mixing station belt conveyor system.
The maintenance of ATA shaft mounted gearbox:
1. Before starting the reducer must be filled of N159 or N220 extreme pressure industrial gear oils, till the gearbox oil shows an intermediate position
2. After three months running, the gearbox need to change oil, attention it must be debris inside the machine rinse before adding new oil.
3. At the reducer hollow shaft ends and drive pulley end gland plate must fastened with locking screws.
4. The reducer pulley and the motor pulley must be parallel when they are installed and the belt tightness should be moderate.
ATA35,ATA40 ATA45 ATA50 ATA60 ATA70 ATA80 ATA100 ATA125
Rated Power:1.1~193KW
Output speed: 25~300
Installation form: Shaft-mounted
| Models | Output Bore Dia. | Maximum Torque | Nominal Ratio(i) |
| ATA30 | 30mm | 180Nm | 5 7 10 12.5 15 20 25 31 |
| ATA35 | 35mm | 420Nm | |
| ATA40 | 40mm/45mm | 950Nm | |
| ATA45 | 45mm/50mm/55mm | 1400Nm | |
| ATA50 | 50mm/55mm/60mm | 2300Nm | |
| ATA60 | 60mm/70mm | 3600Nm | |
| ATA70 | 70mm/85mm | 5100Nm | |
| ATA80 | 80mm/100mm | 7000Nm | |
| ATA100 | 100mm/125mm | 11000Nm | |
| ATA125 | 125mm/135mm | 17000Nm |
| Pre-sale services | 1. Select equipment model. |
| 2.Design and manufacture products according to clients' special requirement. | |
| 3.Train technical personal for clients | |
| Services during selling | 1.Pre-check and accept products ahead of delivery. |
| 2. Help clients to draft solving plans. | |
| After-sale services | 1.Assist clients to prepare for the first construction scheme. |
| 2. Train the first-line operators. | |
| 3.Take initiative to eliminate the trouble rapidly. | |
| 4. Provide technical exchanging. |
){kind=link}